亚洲中文字幕日韩综合,mm131亚洲精品在线观看,成人春色在线观看免费网站,91大神福利在线看

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

electromagnetic induction cylinder Sold to New Zealand

Release time:2023-11-10 08:35:28 Hits: Current position: Home > News

This article mainly introduces:

New Zealand hydraulic cylinder,electromagnetic induction cylinder manufacturer,electromagnetic induction cylinder

New Zealand electromagnetic induction cylinder

(New Zealand electromagnetic induction cylinder,produced by Hengyu Hydraulic Co., Ltd)

electromagnetic induction cylinder are widely used in New Zealand,because of no need for deceleration device,long service life,smooth movement.So our company has designed electromagnetic induction cylinder for customers from New Zealand.

Introduction to electromagnetic induction cylinder:

The repair method of electromagnetic induction cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

electromagnetic induction cylinder piston rod material introduction: In general, we use 45 steel to produce electromagnetic induction cylinder piston rod. It has a large impact force when it is used, and some good performance steel are also used in the heavy load transmission. In order to have enough work intensity when using, and can ensure normal use, this is still more critical to have a detailed understanding of the material.

If the seal of the electromagnetic induction cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and electromagnetic induction cylinder, and the phenomenon of "pulling the electromagnetic induction cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

When the electromagnetic induction cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the electromagnetic induction cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the electromagnetic induction cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the electromagnetic induction cylinder can meet the requirements by grinding. However, the life and reliability of this repair electromagnetic induction cylinder are not high.

Answers to some questions about electromagnetic induction cylinder:

What is the reason for the hydraulic cylinder sticking out and not retracting?
There are two reasons: First, the problem with the seal, if there are two seals on the piston, the top seal is broken. Second, when the hydraulic pressure itself is designed, the rod cavity area is too small, so that the desired return force can not be achieved during the return trip. You can first check whether the coupling is damaged; Then see if the relief valve in the oil line block is blocked. If the use time is too long, it needs to be cleaned, the hydraulic oil is very dirty and can block oil block. Electromagnetic directional valves can also be checked, but the chance of problems is relatively small, unless there is a product problem.

What is the difference between hydraulic piston cylinder and plunger cylinder?
The force surface of the piston cylinder is a rod cavity and a rodless cavity, and the force surface of the plunger cylinder is the plunger, the spring return single-acting piston cylinder can also rely on the external force of the spring to achieve return, the double-acting piston cylinder can produce tension, and the plunger cylinder only produces thrust without tension.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
福利一区二区视频在线| 亚洲精品成人午夜久久| 日本免费一级黄色录像| 日本午夜精品视频在线观看| av一区二区三区天堂| 丝袜美女诱惑在线观看| 久久久免费精品人妻一区二区三区| 国内九一激情白浆发布| 国产成人精品在线播放| 日韩美女偷拍视频久久| 亚洲天堂国产精品久久精品| 最近的中文字幕一区二区| 国产精品乱子伦一区二区三区| 亚洲一区二区三在线播放| 亚洲一区二区三区一区| 亚洲国产精品一区二区毛片| 欧美国产日本高清在线| 人妻内射在线二区一区| 99久久人妻精品免费一区| 午夜福利在线观看免费| 99久久国产精品亚洲| 午夜福利大片亚洲一区| 高潮日韩福利在线观看| 初尝人妻少妇中文字幕在线| 亚洲精品偷拍一区二区三区| 国产精品国产亚洲看不卡| 美日韩一区二区精品系列| 粉嫩国产美女国产av| 香港国产三级久久精品三级| 国产成人免费激情视频| 91熟女大屁股偷偷对白| 亚洲品质一区二区三区| 亚洲精品国产福利在线| 久久一区内射污污内射亚洲| 国产午夜在线精品视频| 日本二区三区在线播放| 东京热男人的天堂一二三区| 亚洲欧美中文字幕精品| 欧美日韩亚洲精品内裤| 熟妇人妻av中文字幕老熟妇| 东京热男人的天堂久久综合|